Updated November 2026

The Work Sharp Precision Adjust Elite knife sharpener is a guided system that lets you set a fixed sharpening angle, pick the right abrasive and restore a worn kitchen knife edge without freehand guesswork. This guide walks you through setup, the sharpening sequence and the adjustments that make the difference between a dull knife and a sharp one. The work sharp precision adjust elite knife sharpener rewards patience and consistent technique more than pressure.

What the Precision Adjust Elite Does

The sharpener clamps your blade in a guide and holds it at an angle you choose, so each pass removes metal evenly along the edge. Its adjustable angle guide lets you set the bevel rather than estimating it by eye. Most kitchen knives fall somewhere in the 15 to 20 degree range per side, and the guide’s markings help you land on a repeatable number. If you are new to sharpening angles, read Work Sharp Precision Adjust Knife Sharpener: Step-by-Step Guide for a broader overview before you start.

Shopping for one? See our guide: How to Use Chef's Choice Knife Sharpener 2 Stage: Steps That Work (2026).

Setting Up the Sharpener for Your Knife

Setup determines most of your results, so take a few minutes before the first stroke. Confirm the blade’s existing bevel angle with a protractor or the guide’s reference marks, then dial the sharpener to match or to a slightly more obtuse angle if the knife is delicate.

  1. Clean the blade and dry it completely so the guide grips without slipping.
  2. Insert the blade into the clamp with the edge exposed about the width of a pencil above the abrasive.
  3. Set the angle adjustment to your target, and lock it.
  4. Check that the blade sits flat against the guide along its full length.

Sharpening Sequence From Coarse to Fine

Work through the grits in order, starting coarse only when the edge is badly chipped or dull. For routine maintenance, begin with a finer stone or ceramic rod. Each stage should leave a uniform scratch pattern before you move on.

  1. Begin with the coarsest stage on a damaged edge, using light, even strokes from heel to tip.
  2. Make 8 to 10 passes per side, alternating sides so you raise a burr on both.
  3. Move to the medium stage and repeat, reducing pressure as you go.
  4. Finish on the finest stage with 5 to 6 light passes per side to polish the edge.
  5. Remove the burr by drawing the blade lightly across a fine surface or using a few passes at the lightest pressure.

Checking Your Progress

Run your thumb carefully across the edge, perpendicular to the blade, to feel for a burr. A raised burr on the opposite side means you are sharpening correctly. You can also test by slicing a sheet of paper; a clean cut without tearing indicates a working edge.

Common Mistakes to Avoid

  • Changing the angle partway through a session, which creates a double bevel that dulls quickly.
  • Pressing too hard, which heats the edge and can ruin temper on softer steels.
  • Skipping the burr removal step, leaving a fragile wire edge that folds over in use.
  • Sharpening a knife that has a serrated section without addressing the serrations separately.
  • Rushing through the grits; each stage is meant to refine the scratch pattern left by the one before.
  • Work Sharp Precision Adjust Elite: the sharpener itself, with the adjustable guide that makes angle setting repeatable. View on Amazon
  • Protractor or angle gauge: useful for confirming the bevel on a knife before you set the guide. View on Amazon
  • Honing rod for maintenance: keeps the edge aligned between full sharpening sessions. View on Amazon

FAQ

How often should I sharpen with this system?

Most home cooks sharpen only when the knife stops slicing cleanly, which may be every few months. Hone the edge with a rod between sharpening sessions to extend the time between full sharpenings.

Can I use it on serrated knives?

The guide is designed for straight edges, so serrated sections need a dedicated tool. Check Sharpener for Serrated Knife: How to Sharpen Serrations at Home for alternatives.

What angle should I set for a chef’s knife?

Many chef’s knives use a bevel in the 15 to 20 degree range per side, depending on the steel and intended use. Check the manufacturer’s specification if you are unsure, and start at the higher end for durability.

Conclusion

The Work Sharp Precision Adjust Elite rewards careful setup and a consistent sequence of grits. Set the angle once, make even passes and finish by removing the burr. With practice, the system gives you a repeatable edge that stays sharp for longer between touch-ups.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our cookware & knives guides, checking product details against manufacturer specifications and owner feedback.