Updated November 2026
The Apex Edge Pro knife sharpener is a guided system that holds your blade at a fixed angle while you work each side on a series of abrasive stones. Once you understand the setup, you can rebuild a dull kitchen knife into a clean, consistent edge in one session. This guide walks through the process from preparation to finishing so you can use the apex edge pro knife sharpener with confidence.
Set Up the Apex Edge Pro Correctly
Before you touch a stone, start with a stable work surface and a clear understanding of the parts. The clamp holds the blade, and the guide rod sets the angle. The stones sit in the holder and move along the rod as you work.
Shopping for one? See our guide: HORL 3 Knife Sharpener Review (2026): Pros, Cons & Who Should Buy.
Check that the clamp is tight and that the guide rod slides smoothly. A loose clamp is the most common reason for an uneven bevel.
Choose the Right Angle for Your Knife
The angle you set determines how sharp the edge is and how long it lasts. Kitchen knives commonly sit between 15 and 20 degrees per side. A lower angle gives a keener edge that dulls faster, while a higher angle holds up better under hard cutting.
Use the angle guides that come with the system, and measure the setting before each session rather than relying on memory. Many home cooks settle on about 17 to 20 degrees for general chef and santoku knives.
Work Through the Stones in Order
Begin with the coarsest stone you need and move toward finer grits. Coarse stones remove metal and reshape a damaged edge. Medium stones refine the bevel, and fine stones polish it.
- Clamp the blade and confirm the angle on the guide rod.
- Start on a coarse stone and make a full pass from heel to tip on one side.
- Count strokes evenly, using the same number on each side.
- Move to a medium stone, then a fine stone, repeating the same pattern.
- Check for a burr along the entire edge before moving on.
Finish and Test the Edge
When a burr forms along the full length of the edge on the opposite side, you have raised metal that needs to come off. Switch to the finest stone and make light passes to remove it. Skipping this step leaves a fragile edge that rolls or chips.
| Stage | Purpose | What to look for |
|---|---|---|
| Coarse stone | Reshape the bevel | Even scratch pattern across the whole edge |
| Medium stone | Refine the bevel | A consistent burr on the opposite side |
| Fine stone | Polish and remove burr | Burr gone, edge smooth to the touch |
To test sharpness, slice a sheet of paper or a ripe tomato. A clean cut with little resistance means the edge is working. If the knife tears or drags, repeat the fine stone passes with lighter pressure.
Common Mistakes
- Changing the angle partway through a side, which creates a rounded or uneven bevel.
- Pressing too hard, which can overheat the blade and wear the stone unevenly.
- Skipping the coarse stone on a dull knife, which makes the process much longer.
- Stopping before the burr forms along the full edge.
- Sharpening a knife that is badly chipped without first checking whether it needs repair.
Recommended Gear
Keeping the stones flat and the setup stable makes a visible difference in results.
- A stone flattening plate keeps the sharpening surface even so the bevel stays consistent over time. View on Amazon
- A cutting board with a non-slip base holds the sharpener steady while you work. View on Amazon
- A honing rod helps maintain the edge between full sharpening sessions. View on Amazon
FAQ
How often should I sharpen my kitchen knives with the Apex Edge Pro?
Most home cooks do a full sharpening session every few months and touch up with a honing rod in between. Heavy daily use may call for more frequent sessions.
Can I use the Apex Edge Pro on serrated knives?
The system is designed for straight edges. Serrated blades need a specialized tool, since the stones cannot follow the scalloped profile.
Do I need to remove the knife from the clamp between stones?
No. Keep the blade in the clamp and the angle locked for the entire process. Removing it between stones risks changing the angle and creating an uneven edge.
Conclusion
With a correct setup, the right angle, and a disciplined progression through the stones, the Apex Edge Pro gives you a repeatable, sharp edge. Take your time with the burr removal, and check your results with a simple cutting test. Consistent practice will make each session faster and more predictable.
Related reading
- Wicked Edge Knife Sharpener Review: Is It Worth It?
- Tru Hone Knife Sharpener: Step-by-Step Guide to Sharper Edges
- Knife Sharpener Leather Strop: How to Strop a Knife Edge Step by Step
- Kitchen Q Knife Sharpener: How to Use One for Sharper Edges
- Is the Knife Sharpener Kitchen IQ Worth Buying? Pros, Cons and Tips

