Updated November 2026
A ruixin pro knife sharpener is a guided, pull-through style tool designed to bring a dull kitchen knife back to a usable edge with a few controlled passes. In this guide you will learn how to prepare your knife, set the correct angle, sharpen in a consistent sequence and check your results. The process takes a few minutes once you know the routine, and it is the most reliable way to keep a chef knife or paring knife performing well between professional sharpenings.
What You Need Before You Start
Good results depend more on preparation than on speed. Gather the right supplies first so you are not stopping mid-edge to hunt for a towel.
Shopping for one? See our guide: HORL 3 Knife Sharpener Review (2026): Pros, Cons & Who Should Buy.
- The ruixin pro knife sharpener, placed on a stable, non-slip surface
- A clean, dry cutting board or towel to keep the sharpener from sliding
- Dish soap and warm water for washing the blade before and after
- A cutting board or piece of paper for the paper test
- Your knife, with the blade free of food residue and loose debris
Step-by-Step: Sharpening a Knife with a ruixin pro knife sharpener
Work through the steps in order. Rushing the setup is the most common reason edges come out uneven.
- Clean and dry the blade. Oil or grease will reduce grip and can hide the edge you are trying to see.
- Identify the slots. Most guided sharpeners have a coarse stage for repairing damage and a finer stage for refining. Start with the coarse slot only if the knife is badly dull or chipped.
- Seat the blade at the guide. Place the spine against the guide, keeping the edge centered in the slot. Check the manufacturer’s diagram for the correct angle for your knife type.
- Apply light, even pressure. Draw the blade through the slot from heel to tip, keeping the same angle the whole way. Four to six strokes per side is a reasonable starting point for a moderately dull knife.
- Alternate sides. Sharpen the opposite side the same number of times to keep the edge balanced.
- Move to the fine stage. Repeat with fewer strokes, around three to four per side, to refine the edge and remove the burr.
- Test the edge. Slice a sheet of printer paper with light pressure. A clean cut means the edge is working; tearing or catching means more passes are needed.
Checking Angle and Edge Quality
Angle is the factor that most affects how sharp a knife feels and how long the edge lasts. Guided sharpeners reduce guesswork, but you still need to confirm the knife is seated correctly.
| Knife type | What to check |
|---|---|
| Western chef knife | Edge centered in the slot, consistent contact from heel to tip |
| Asian-style thin blade | Confirm the guide setting matches the narrower edge angle |
| Paring knife | Use lighter pressure to avoid rounding the small tip |
If the burr (a thin wire of metal) is still present on one side after both passes, you are likely applying more pressure on one side or drifting off the guide. Slow down and keep the spine firmly against the guide.
Caring for Your Knife Between Sharpenings
Sharpening restores the edge, but daily habits decide how often you need to do it. Hand-wash your knives, dry them immediately and store them on a magnetic strip, in a block or in a sheath rather than loose in a drawer. Use a wood or plastic cutting board, since glass and stone will dull the edge quickly. For guidance on keeping an edge between full sessions, see Knife Sharpener Kitchen IQ alternatives and general sharpening routines covered in Knife Sharpener for Kitchen: A Step-by-Step Guide for Home Cooks.
Common Mistakes
- Pressing too hard. Heavy pressure can remove metal faster than necessary and shorten the life of the blade.
- Sharpening the whole length of a serrated blade. Serrations need a dedicated tool, as explained in Sharpener for Serrated Knife: How to Sharpen Serrations at Home.
- Skipping the fine stage. A coarse-only edge can feel rough and tear food.
- Sharpening a ceramic blade with a metal-based guide. Check compatibility first; see Sharpener for Ceramic Knife: What Works and How to Use It (2026).
- Ignoring the burr. If you do not remove it, the edge will feel dull almost immediately.
Recommended Gear
A few supporting items make maintenance easier and more consistent.
- A sturdy cutting board, since a stable surface keeps the sharpener from shifting during passes. View on Amazon
- A knife guard or sheath for safe storage between uses and transport. View on Amazon
- A honing rod for realigning the edge between full sharpening sessions. View on Amazon
FAQ
How often should I sharpen my knives?
Home cooks who use their knives daily often sharpen every few weeks, while lighter use may need it only every few months. Regular honing between sessions extends the time between full sharpenings.
Can I use a ruixin pro knife sharpener on any knife?
Most guided sharpeners work best on standard straight-edged kitchen knives. Check the manufacturer’s guidance for ceramic, serrated or very thin blades before using it.
Why does my knife still feel dull after sharpening?
The most likely causes are an inconsistent angle or skipping the fine stage. Clean the blade, confirm the seating, and run the paper test again.
Conclusion
Using a ruixin pro knife sharpener is straightforward once you follow a consistent routine: clean the blade, seat it correctly, sharpen evenly on both sides and finish with a fine pass. Check the edge with the paper test and keep your knives stored safely between uses. Consistent habits will give you a sharper, safer knife for years.

