Updated November 2026

A longzon 4-in-1 knife sharpener lets you restore a dull kitchen knife in a few minutes without a whetstone or a learning curve. This guide walks through what the four stages do, how to run a knife through them, and how to keep the edge sharp afterward. Expect a practical routine you can repeat every few weeks.

Understand What Each Stage Does

Most 4-in-1 pull-through sharpeners use a sequence of slots, each with a different abrasive or shape. The coarse stage reshapes a damaged or badly dulled edge, while the finer stages refine the bevel and polish it. Manufacturers generally recommend starting at the coarsest slot only when the knife is really dull, because using it too often wears metal away quickly.

Shopping for one? See our guide: HORL 3 Knife Sharpener Review (2026): Pros, Cons & Who Should Buy.

If your knife still cuts a tomato cleanly, skip straight to the fine stage. That keeps the blade thicker over the long run and gives you a sharper result than overworking it.

Step-by-Step Sharpening Process

Work through the slots in order, using the same number of passes at each stage. Keep the knife upright and let the guides hold the angle for you.

  1. Wipe the blade dry and check that the sharpener sits flat on a stable counter.
  2. Place the heel of the blade at the entry of the coarse slot, with the spine resting against the guide.
  3. Pull the knife through toward you in one smooth stroke, applying light, even pressure. Do not press down hard.
  4. Repeat 3 to 5 passes at the coarse stage for a badly dull blade, or 1 to 2 passes for a moderately dull one.
  5. Move to the next slot and make 3 to 5 passes, then continue to the finer stages.
  6. Finish with the ceramic or polishing stage, usually 2 to 3 passes, to refine the edge.
  7. Wipe the blade with a clean cloth to remove metal particles before using the knife.

Checking Your Results

Test the edge by slicing a sheet of paper or a ripe tomato. A properly sharpened blade should pass through without tearing or dragging. If it still snags, make one or two more passes at the finest stage rather than returning to the coarse slot.

Keep the Angle Consistent

Angle is the most common source of poor results with pull-through sharpeners. Keep the spine of the knife in contact with the guide, and avoid rocking the blade side to side. If the edge feels uneven, check whether you are tilting the handle upward as you pull.

Knife condition Suggested starting stage Typical passes
Chipped or badly dull Coarse 3 to 5, then move up
Dull but intact Medium 2 to 4
Slightly dull Fine or polish 1 to 3

Maintain the Edge Between Sharpenings

Regular light use keeps an edge sharp far longer than occasional heavy sharpening. Pull the knife through the fine stage every few weeks, or whenever it stops slicing cleanly. Store knives in a block or on a magnetic strip so the edge does not strike other metal. For a broader look at honing and maintenance routines, see Knife Sharpener Honing Rod: How to Hone a Knife Properly in 5 Steps.

Common Mistakes

  • Using the coarse slot every time, which removes more metal than necessary.
  • Pressing down hard, which can bend a thin blade or cause uneven wear.
  • Sharpening serrated knives in the standard slots, since serrations need a different tool.
  • Skipping the cleanup wipe, leaving metal filings on the cutting edge.
  • Pulling the knife back and forth through the slot instead of one direction, which can gouge the edge.

A cutting board with a stable base keeps the sharpener from sliding while you work. View on Amazon

A soft microfiber cloth helps you remove metal dust after sharpening so it does not end up in your food. View on Amazon

FAQ

How often should I use a longzon 4-in-1 knife sharpener?

For a home kitchen, a light pass through the fine stage every few weeks is usually enough. Use the coarse stage only when the knife is visibly dull or chipped.

Can I use it on serrated knives?

Standard pull-through slots are designed for straight edges. Serrated blades need a tool with shaped stones or a dedicated serration slot.

Will it damage my knife over time?

Overuse of the coarse stage removes more steel than needed. Limiting coarse passes and using light pressure keeps the blade in good condition for longer.

Conclusion

A longzon 4-in-1 knife sharpener works best when you match the stage to the knife’s condition and keep your passes consistent. Start coarse only when needed, finish fine, and wipe the blade clean each time. With a short routine every few weeks, your knives will cut cleanly for everyday cooking.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our cookware & knives guides, checking product details against manufacturer specifications and owner feedback.